Home

Same ssid for 2.4 and 5ghz

I use the same SSID For 2.4 & 5. It avoids confusion with anyone in the house on what to connect to and when. Usually when I'm in the same room as an AP, it will connect to 5Ghz. When I'm not as close, 2.4. Works for me. I also have a Guest SSID, so instead of 4 SSIDs, I only have 2 some devices dont handle switching to the 5GHZ channel as well as they should. Specifically older android phones (i have a lg x power), it will connect fine at 2.4 and can connect fine at 5ghz but if the ssid is the same it will only connect at 2.4 Hi all, So I'm pretty familiar with my way around my linksys routers, but last night I came across a concept that I found very intriguing. I had a WRT610N in the past, and always assumed that I needed to have a separate 5ghz network, with its own independent SSID, as well as the same for the 2.4ghz network 2.4 and 5 each have pros/cons. While 5 is faster, it has less range. Crippling the the 2.4 by setting lower power seems to be pretty much throwing in the towel on any longer range usage. Now a device that might otherwise work fine in the home is out of luck because 5 can't reach it and you just pu Hello everyone, I live at a shared flat sort of thing with included wifi and I hacked the router and saw, that the router uses 2.4 and 5ghz band under the same SSID

2.4 and 5 ghz same SSID or different SmallNetBuilder Forum

  1. R8500 - Set up same SSID in 2,4Ghz and 5Ghz band Hello everybody. I'm going to buy the new R8500, but before I wan't to know if now is possible to set up the same SSID in the 2,4Ghz and 5Ghz Band
  2. Counterpoint to those having problems with their Wyze Cams on networks with same SSID names for both 2.4 & 5 GHZ. I have two networks at two different sites where the 2.4 GHZ and 5GHZ share the same SSID name, and they both work perfectly
  3. I just got a new E2500 and out of the box the system uses the same SSID for 2.4 GHz and 5 GHz. Obviously you CAN configure them to use different SSID's, though. Should I make them different or keep them the same? I don't really want to mess around with having 2 different SSID's if I don't get a real benefit

I have the same issue - 2.4 and 5ghz with different ssid's are being treated as different networks: for example I have a wireless speaker (airplay) that is connected to my 2.4 wireless network. If my ipad or ipod are attached to the 2.4 network then they can access the speaker If you have the ability, do both. Broadcast the same SSID on both bands, and then also broadcast a 2.4/5 version for devices where you might want to pin to one or the other. Band steering is the real solution here, but not many APs support that (and it isn't really part of the spec) Older 2.4Ghz only devices will just connect to the 2.4Ghz frequency and not even see the 5Ghz frequency, so having the same SSID will work fine for them. Cons of naming the SSIDs the same: Different brands of devices may behave differently between 2.4Ghz and 5Ghz frequencies The benefit of using different SSIDs on 2.4 and 5GHz is that you can explicitly control which devices use 2.4 and which use 5GHz by selecting the desired SSID on each device. You might want to do this if you have a device which irrationally prefers associating on 2.4 instead of 5GHz A simultaneous dual-brand router broadcasts separate 2.4 GHz and 5 GHz Wi-Fi networks at the same time, giving you two Wi-Fi networks that you can choose from when you set up a device. Some router brands also let you assign the same SSID to the two bands so that devices only see a single network—even though both are still operational

The downside to having a different SSID for 2.4 and 5GHz is you are most likely to connect to 2.4 when you arrive at home since it travels further, and you will have to manually connect to the 5GHz network every time. The same name, again, generally will intelligently switch to the 5GHz network if it's strong enough Since I've given them both the same SSID I've never seen two show up with the same name. That's why I assumed any 5GHz device would be smart enough to pick which one to be on. If I label one 2.4 and the other 5, then they both show up on my network list and I have to then research what device connects to what network, etc

Should you use the same SSID for 2.4Ghz and 5Ghz? 4 posts KallDrexx. Ars Tribunus Militum One SSID and password for all 3, 2.4 and 5 GHz, different channels of course. It seems to work pretty. 1. Use same SSID for all radios on the same network (be they 2.4GHz or 5GHz). If you have one network in your home but have either multiple routers/access points for better coverage or multiple.

Naming 2.4 and 5GHz networks - same or different name ..

Separate 5ghz and 2

  1. It depends on your device. Even with the same SSID, devices see the two signals as different WiFi signals. Usually, devices are designed to use the strongest signal. 5 GHz doesn't propagate through walls and floors as well as 2.4, so if you aren't close to the router, you will likely be connected to 2.4
  2. From the documentation on the AP it looks like it can broadcast 2 BSSIDs with the same SSID. One on 2.4 Ghz and one on 5 GHz. Devices see one SSID and those that can connect on 5 are connected on 5 (a/n) and devices that can only connect on 2.4 (b/g/n) fail-over to 2.4. I can't find instructions to do this
  3. some devices have the 2.4 GHz radio and some have the 5 GHz radio and many of the newer devices have a choice. 2.4 GHz being for furthering your distance, or the 5 GHz band for faster speeds but shorter distances. it is always advisable to separate the SSID names like home_2.4 and home_5.0. this way let the devices chose the better connection
  4. The problem in this case is that, since the OnHub uses the same name for both the 2.4 and 5GHz SSIDs, a 2.4GHz-only device (in this case, the BloomSky) either can't connect, or has trouble staying connected, because it can't tell whether it's connecting to a 2.4 or a 5GHz network (same deal with v1 Chromecast; it may connect initially.
  5. If the technology was perfect, it would be an easy choice: turn on 2.4GHz and 5GHz; give them the exact same SSID, password, and encryption settings; and your device will automatically pick the 5GHz network when you're close to the router and switch to 2.4 when 5 gets weak. In practice, band steering is a bit unreliable
  6. Re: Same SSID for 2,4 and 5 Ghz Tue May 23, 2017 12:21 pm What I mean is that Windows starts at 2.4 as it is most common signal, not necessarily stronger, so chance for fast association is bigger for 2.4 than for 5GHz

it would be nice to find a way to tell the shield to prefer 5Ghz over 2.4 or at the very least for it to be able to automatically connect to 5Ghz when there's a single SSID with the 2.4Ghz broadcast disabled. at the moment it looks like it tries to connect to 2.4Ghz and if it can't just gives up even if the router does bandsteering and 5Ghz is. You can create a different SSID for the 2.4Ghz band and 5Ghz band on the same UAP. You can create a different SSID for the 2.4Ghz band and 5Ghz band on the same UAP. 2.4 GHz vs 5 GHz WiFi. Hello Dears, In a Controller-Mode AP's, is it possible to have both 2.4GHz & 5GHz under the same SSID? If that's possible, will there be any criteria for bindig a device to either 2.4 or 5Ghz? Can What this means is that you will only get 300 meg on the 5 ghz side. On the 2.4 side you will get 144 at best, due to non bonding. My stance is allow guest on both, so one 1 ssid. You wll get a mix of guest on 2.4 and 5 ghz. Unless there are compelling reasons not to. As for 5 Ghz and adoption, almost all new devices support 5 GHz and 802.11n

Solved: 2.4/5 GHz same SSID - Ubiquiti Networks Communit

What are the differences between 2.4 and 5 GHz? Let's start by saying that these two bands are numbers that your WiFi can use for its signal. The main difference between 2.4 Ghz and 5 GHz is the speed. In theory, 2.4 GHz WiFi supports up to 450 Mbps or 600 Mbps, but this depends on the type of router. 5 GHz WiFi supports up to 1300 Mbps Forum discussion: Is it best practice to have separate SSID names of the 2.4 and 5 Ghz bands on a router? Is there any issue with setting them up identically (i.e. same SSID and WPA2 password) so.

Connect to 5ghz wifi with same SSID as 2

  1. der: Your Wifi point(s) uses the same network name for both the 2.4 and 5 GHz bands. We believe this simplifies the Wi-Fi experience
  2. ds.
  3. Posted: Wed Sep 06, 2017 15:41 Post subject: wifi 2.4 and 5 Ghz: Hello I am trying to test the Linksys EA6350. I am wondering about the 2.4Ghz and 5Ghz For the SSID should the same SSID be put in 2.4Ghz and 5Ghz so that the client automatically connects to the best according to his device
  4. Re: Should 2ghz and 5ghz SSID's have different names The biggest advantage is knowing which connection your device is on using different names. The 2.4Ghz is very common for many everyday items from microwave ovens, garage door openers, some wireless house phones, npbaby monitors, and other routers to name a few
  5. ish the risk of some wannabe hacker

But, some users swear by assigning a separate name to the 2.4 GHz and 5 GHz bands, and they can make a good argument for doing this. Their reasoning usually goes along the lines of my router does 5 GHz and I want to connect to 5 GHz. To do that, they point their laptop at the 5 GHz band SSID and connect I need my 2.4 and 5ghz channels' SSIDs to be unique from each other, also for security purposes. I'd like to do one of two things; access airties settings to allow me to change each SSID separately and/or disable the wifi radio (if I want it to only function on the 5ghz frequency)? What is the difference between 2.4 GHz and 5 GHz WiFi? Which network should you use on the dual band selection screen? 2.4 GHz vs 5 GHz WiFi | What Is The Difference? Eric's Home Network. If you think about it, it's really no different than having multiple WAPs with the same SSID (such as you might in an office or other large space) and a device connecting to whichever one has the strongest signal. That the two signals a device sees happen to be in different bands and also happen to emanate from the same box is irrelevant

R8500 - Set up same SSID in 2,4Ghz and 5Ghz band - Netgea

  1. g them both the same. Any computer connecting is still going to the same router and using the same IP scheme that your router is setup for
  2. They told me that, if it is on a network that has a 2.4 and a 5GHz network, and the SSIDs for both are exactly the same, this problem can happen. I said why, the router/AP may be trying to move the client to the other SSID. There is no physical way for the 2.4Ghz ONLY Chromecast (client) to see, or know anything about, the 5Ghz band and it's.
  3. Clients should be able to switch between 2,4 and 5GHz how ever they want, basically they should prefer the 5GHz network and only switch to 2,4GHz when signal is weak. What I did so far: I setup my RT-AC87U with both frequencies based on this guide. Basically I have the 2,4 and 5GHz network running on the same SSID
  4. Many devices only use the 2.4 GHz frequency, and these devices are all attempting to use the same radio space which can cause overcrowding of the channels. The 5GHz band has 23 available channels for devices to use vs the 3 available on the 2.4 GHz band. Overcrowding and interference can cause slower speeds and intermtent connectivy issues
  5. The good thing about dual-band routers is if you have devices that can only run on 2.4, like our old TiVo wifi adapter, those devices can connect at 2.4GHz, while your new-fangled devices can play happily in the much less congested space of 5GHz

SSID same for 2.4Ghz & 5 Ghz interferes with remote viewin

Pros/Cons same SSID for 2

I went into her Linksys web settings and gave her bands different SSID names now named Linksys 2.4 GHz & 5 GHz hoping the smart plug would be able to connect at 2.4. Here's my issue since naming the SSID's differently I can only connect at 5 GHz not 2.4 Splitting SSID / Separating 2.4 and 5 GHz Mark as New ; Bookmark One network will be the same name as usual and will be 2.4GHz band and the other will be the. If you can configure the TG1582G so that the 2.4GHz and 5GHz Network Names (SSID) are the same, and they both have the same password, then the Mac, iPhone or iPad may decide to jump from one.

Netgear R6300 2.4 and 5ghz same SSID

Can someone guide or correct me with my set up, I have 3 SSID set up on ZF7982 Standalone ( with latest firmware ) on both band 2.4 & 5Ghz and wondering if I have them set up correctly or wrong My set up goes as follow: SSID#1 2.4Ghz & 5Ghz for legacy AV... SSID#2 2.4Ghz & 5Ghz for laptop, Tablet, Smartphone.. In some deployments, multiple SSIDs are enabled on an a single AP. Some SSIDs may have legacy bit rates disabled which shortens the coverage radius on 2.4 GHz or the SSID may only have 5 GHz enabled. The site survey should measure the coverage cells of each SSID independently within the extended service set to determine if adequate coverage is. Technology is an odd duck: in less than twenty years, Wi-Fi has gone from an amazing (and expensive) luxury to an assumed inclusion in every device you own. And yet, there's plenty of room for improvementwhich is why you should consider disabling the old 2.4GHz band on your home's Wi-Fi network and using the newer, faster, less crowded 5GHz band exclusively Ok, so with a dual band router, you get both 2.4 GHz and 5 GHz channels, and you can either give them both the same SSID and password, or give them separate SSIDs/passwords If you log into the router, add a 5 to the 5Ghz SSID and untick the synch with 5Ghz on the 2.4 section. Apple devices in particular don't like it when both are the same name. Message 3 of

If you have a wireless router (802.11n or newer), chances are it offers WiFi on two separate bands (dual bands): 2.4GHz and 5GHz.You may have noticed this as you searched for your Wi-Fi network on a new device and noticed that there were two (or even three) with the same name, but one (or two) was designed for 5GHz service Wireless Networks Thread, 2.4 and 5ghz - Same SSID or Seperate? in Technical; Morning All, Still playing around with our 2 wireless networks (Yes 2) to try to get it to work properly. Is it better to have 5GHZ clients on their own SSID or use an SSID which works with both 2.4 and 5GHZ (using the default when creating a new wireless network)? I started out with an older access point which had to have separate SSIDs for both 2.4 and 5GHZ, and since moving to the UTM I migrated to a single SSID for both 2.4 and 5GHZ So, what really is the difference between a 2.4GHz and 5GHz WiFi? Well, we will tell you what? You might already have heard of both these terms. When we talk about the dual-band WiFi, these, the 2.4 and 5Ghz WiFi bands refer to it

802.11ac, 2.4GHz and 5GHz on same SSID or different

My router can have different SSIDs for 2.4 and 5 GHz and I'm not sure if it's better to have the same SSID or not. Initially I put the same network but I got confused when the MacBook Pro displayed me two networks with the same name, an I was not able to distinguish between then Solved: Can the 2.4 and 5 GHZ SSID names be the same on a home gateway max TG799 and I just let the devices work out which one to connect to or will this cause some sort of conflict

Should I Name My 2.4GHz & 5GHz Wireless Networks the Same ..

  1. g possible between them without going to a radius server. I dont need super fast handoffs, they just need to roam reliably well. I am planning on going to channels 1,6,11 for the 2.4ghz radio. For the 5ghz radio, should I be using 20mhz or 40mhz
  2. I have re-tested the issue to confirm that it exists. When matching the SSID's for the 2.4Ghz and 5Ghz bands the battery drain is back up to around 6-15% when on standby. It looks like W10M might have an issue with routers that broadcast the same SSID for both bands
  3. utes) and once it's done, you should see 2 different SSID on your wifi scanner and you can double check it through your Orbi dashboard : the name will be different on the main dashboard between 2.4 and 5Ghz
  4. If desired, the SSID of the SBG6782 can be changed to a new SSID of choice. This document describes how to change the 2.4 GHz and.or 5 GHz SSID of the SBG6782 wireless primary network. NOTE: It is recommended to change the SSID from a computer that is connected to the SBG6782 with an Ethernet cable
  5. Both use the same SSID, both have 2.4GHz and 5GHz bands enabled. But my Android devices mostly connect the 2.4GHz band - even if I stand next to the router or repeater, and thus the 5GHz signal is quite strong. I want them to prefer the 5GHz band if available (and strong enough), but use the 2.4GHz otherwise

The 5 GHz has a wider wireless spectrum available compared to the 2.4 GHz, which leads to significantly better performance as the 5 GHz is commonly used for usage that requires uninterrupted throughput. That is why it is recommended for media streaming and transferring music, pictures, and video throughout your home network Yes, Multy X allows user to use different WiFi SSIDs for 2.4GHz and 5GHz in the network. But there will be two separated WiFi networks (one for the 2.4GHz band and the other for the 5GHz band) which require you to manually connect to the band you want to connect and the band steering feature will be disabled Basically, I have a modem/router combo provided by my ISP which is quite good, broadcasts the same SSID at 2.4 and 5GHz at the same time, but it's too far away from my Switch. I have set up a Linksys E900 with Tomato as a wireless repeater bridge and am wondering if setting its SSID to the same one as my main router's will cause any problems

What are the benefits and disadvantages of using different

As many people know, the 5 GHz WiFi band is going to provide better performance and is less crowded than the 2.4 GHz band. I have always tried to get my devices on 5 GHz. Most WiFi access points/routers broadcast the same SSID for both 2.4 GHz and 5 GHz allowing devices that support both bands to pick which band it wants to use - If you're in a residential neighborhood (without anybody stacked on top and below you) then, you'll want to use both 2.4Ghz and 5Ghz by having both networks using the same SSID (wifi name), and you might even want to consider a central location where to put your router (main floor, centrally-located, and forget the old basement computer desk. I'm using an Android app to test a user's WiFi network for specific hardware compatibility. The hardware that I am testing for supports 2.4 GHz networks only. In particular I want to be able to connect to a 2.4GHz network when there is a 2.4GHz network and 5GHz network in range with the same SSID/PSK Question is: with which network does you're iPhone connect, the 2.4 or the 5ghz? Since you have the same ssid my guess would be it connects to the 2.4 network since this will be the strongest one. If you do it like I've said two post ago, you're iPhone has aconnection with the 5ghz and the watch will be connected to the 2.4

Same problem here with our University wifi. Cause has to do with roaming. I've your connected to the 2.4 because youre roaming, it doesn't get you bac up the 5.ghz until you disconnect and connect the wifi again. Driver should work like for instance the intel centrino's N6205. Allowed band b,g,a,n and prefered 5Ghz. Eri Your VLAN ID for a particular SSID does not match on the 2.4 GHz and 5 GHz frequencies. You must create the same VLAN ID for the same SSID for both frequencies. Important Note About the Scheduler Featur Generally 5Ghz when your quite close, but it degrades quicker then 2.4Ghz due to distance and obsticales. If you leave both with the same SSID then the device trying to connect will attempt to use the best connection and will swap between 5 and 2.4 depending on conditions and if it can only handle 2.4 it will connect to 2.4 et

One additional note: You should consider using the same SSID (WiFi network name) for your 2.4 GHz and 5 GHz band. That will allow roaming clients to dynamically choose the band that works best for them at any given time I'm trying to determine whether iOS prefers 2.4 or 5 Ghz when all things are equal. The reason I ask is that I've read that Apple recommends using the same SSID and security settings for multiple Wifi networks and that people have reported that iOS prefers 5 Ghz in that set up, but I haven't found that to be the case Hello. I have just got the superhub 3. The 5ghz signal struggles to reach the top floor in my house. Is there any way of configuring the individual SSID's for 2.4 and 5 ghz bands so I can choose the 2.4ghz ban

Video: What's the Difference Between 2

2.4 and 5GHz under same or different SSID? : HomeNetworkin

However, both the mesh portal and the mesh point are broadcasting the client ssid on both 2.4 and 5Ghz. I'd like to use 5Ghz for the mesh link and 2.4 Ghz for the client ssid. I can't figure out the magic combination that will allow this. I can add an 802.11a radio profile that has radio enable unchecked to the mesh ap group Different SSID for 2.4 and 5 GHz « on: December 10, 2018, 07:05:01 PM » I have a new DIR-867 which I am using as an access point (Static IP address and turned off DHCP, connect LAN port to my existing router) If you choose to use 5 ghz over 2.4 ghz , because of the shorter range on the 5 ghz wifi, your 5 ghz network has less chances of interfering with neighbor's 5 ghz. 3. 2.4 ghz vs 5 ghz Data Throughput 5 ghz offers faster speed since more data can be transferred via the 5 ghz band You'd know which one you are connected to because the 5 Ghz usually has -5ghz written after the ssid. If not, then settings have been changed in the router and it would be a good idea to revert it back. To have your phone only connect to 5ghz, just make it forget the other one and it will connect to 5ghz every time

Setting up new router

I am trying to setup Capsman to support havin separate SSID for 2,4 GHz and 5 GHz.. Before I used the same SSID for both, but I want to be able to choose 5 GHz for increased speed... BUT, as I started to change - basically whatever I do fails... And Capsman is totally unstable.. As is, I will have to remove Capsman entirely as it does not work. Re: Separate SSID for 2.5 and 5 GHz I've set the name and password for 2.4 and 5 for my iPhone 6 plus and iPad Air 2. The tech told me, to sign into both and it will use 5.0, which it does Slipeh, Apr 7, 2015: Scenario; I have an AC Router (ASUS RT-AC68U) which supports 2.4ghz and 5GHz network. I have 2 networks setup with similar SSID (IP on you 2.4 and IP on you 5) - one for 2.4ghz devices and one for 5ghz devices I have a printer that only works with 2.4 and it is able to connect because the system gives it a 2.4 band even though the SSID is the same. I am not a Comcast Employee. I am just a customer, volunteering my time to help other customers here in the Forums

Should you use the same SSID for 2

But don't let that deter you from testing out 5GHz. If your router supports Dual Band, or even Tri Band, you can create multiple independent wireless networks at the same time, one on the 2.4GHz band for the increased range and compatibility with legacy devices, the other on the 5GHz band, with shorter range but less interference. Perfect for. If your SSID isn't unique, Wi-Fi devices will have trouble identifying your network. This could cause them to fail to automatically connect to your network, or to connect to other networks that share the same SSID. It might also prevent Wi-Fi devices from using all routers in your network, or prevent them from using all available bands of a router It is advertising same SSID in both the bands (2.4 GHz and 5 GHz). Raspberry Pi 3 running 2016-05-31 raspbian-jessie-lite + our application software (that has no modification for WiFi module) is not able to connect to even 2.4 GHz band. If we turn off 5 GHz for the same SSID (advertising only in 2.4 GHz band) , it is able to connect

The 2.4 GHz band does provides greater distance for the connection while the 5 GHz band provides higher speed in shorter distances for the connection. As the 2.4 GHz and 5 GHz bands share the same Network Name (SSID), it is recommended to disable Band Steering to reduce the confusion on the Wi-Fi client If you had named from 2.4 and 5 bands with the same SSID and you connected to the network using a late model device which is capable of 5g - would it by default connect to the 5G channel Helo All, Is there a way to allow an SSID in the sonicwall built-in WiFi (not sonicpoints) to employ both the 2.4GHz and the 5GHz band or a dedicated SSID for each frequency like some home routers allow Same SSID for 2.4Ghz and 5Ghz Networks? Mini Spy No sc302 he has 1 AP his router, and he is using the same ssid for 2.4 and 5.. Share this post. Link to post Share on other sites. 0

4 Wi-Fi Tips from Former Apple Wi-Fi Engineer - The Mac Observe

You can use the same Wi-Fi settings for both the 2.4 GHz and 5 GHz bands or use different settings for each band They continued to have problems so they bought dual band router but were still having the same issues. I looked at the router and they had named the 2.4 and 5 Ghz networks the same SSID. I was not seeing the 5Ghz on any of their devices. When I put a _5G at the end of the SSID the devices starting seeing the SSID for the 5 Ghz only

My UK BT router has two Wifi frequencies 2.4 and 5 GHz and the odd occasion I have Iooked at the router info, on the router itself, I noticed that it always seemed to use 2.4 GHz. Out of curiosity I investigated it last night and found that iPads and iPhones generally do not seem to like the same SSID used for both frequencies Few weeks ago I was able to configure my cisco AP 1131 AG. I wanted to configure this device with 2 channel frequencies. 1 at 2.4Ghz and 1 at 5Ghz, both frequencies had to be in the same SSID Yes. iPad will do 2.4 or 5Ghz. Should I use only one band? or both? If you have a dual-band router that works simmultaneously on 2.4 and 5Ghz with the same SSID then the iPad will pick one to connect to. I found that it usually picked the 5Ghz but sometimes would pick the 2.4Ghz. Once it picked one it would stay on that until disconnected The only problem with disabling the 2.4 band, is that if you are having issues with 5ghz reception, the device goes offline. 2.4ghz travels farther and has better CRC, when it comes to distance and when a device goes into power saving mode and turns off the 5ghz radio, or decreases the power of the radio to conserve battery power A frequency band refers to a particular frequency range within which signals can be sent. WLAN waves can be transmitted via the two frequency bands 2.4 GHz (GHz = gigahertz) and 5 GHz. These differ in speed and distance. In short, the 2.4 GHz network radiates further but is therefore slower, while the 5 GHz network is faster but does not reach.

populär: